How to Fix – Netgear Router Keeps Changing IP

Gone are the times when you need to move around your house to check whether the internet connection strength is strong or weak. All thanks to Netgear routers that blanket every corner of the house with ultra-fast internet strength. Thus, lagging internet signals have become folk tales. But, you cannot use the internet on your devices via the Netgear router until your router assigns an IP address to them.

FYI, each time you try to access the router’s network, a new IP is provided to your device so that you can use the internet. But, there are times when the Netgear router keeps changing IP of devices accessing its WiFi. In that scenario, your chances of falling victim to the routerlogin not working increase. Therefore, you should address the problem as soon as you notice it. Highlighted in this write-up are the hacks that will pull you out of the well of the issue you are facing. Read on.

[Solved] Netgear Router Keeps Changing IP

Avoid Power Fluctuations

The first and the root cause of various Netgear router issues is a fluctuation in the power supply. It happens in two cases. First, when you’ve utilized a damaged power socket to do the job of supplying electricity to the router. The second scenario is likely to occur when there are sudden power outages in your locality. No matter to which lot you belong, both situations have workarounds. Get the socket repaired or replaced if your router is getting an inconsistent power supply due to a damaged one. However, you need to use a UPS to compensate for sudden power outages. This way, your Netgear router won’t turn off due to an abrupt power cut.

Rectify the Modem-Router Connection

The router transmits the signal emitted by the modem. Therefore, there are chances that the IP change issue has occurred due to a weak connection between them. Remember, when we say the modem-router connection, we’re referring to the distance separating your devices or the Ethernet cable used to join them. The Ethernet cable needs to be paid attention to if you’ve used a wireless connection for your devices. Is it worn out? If you’re nodding your head in yes, then pull in another Ethernet cable. However, the connection must not be loose at any cost. On the other hand, you have to check the distance if a wireless source has been used to connect the WiFi devices. It must neither be too less nor too much.

Get Rid of WiFi Disruptions

Signal interference is another factor that might be resulting in the emergence of the Netgear router keeps changing IP issue. This is to inform you that WiFi signals are electromagnetic waves that if come in contact with other EM waves get distorted. Therefore, you need to eliminate all devices that run on the principle of EM wave transmission. We’re not asking you to discard them. But, you need to keep your Netgear WiFi router away from those devices. In addition, you need to place the router away from lustrous surfaces because they tend to bounce signals. Water bodies like geysers and reverse osmosis systems are also supposed to be a few meters away from the wireless router.

Restart the Router

Restarting the router can also help you do away with the IP change issue. Sometimes, neither the modem-router connection nor the router’s poor location is the reason. It is a technical glitch that does not allow the device accessing your router to have the same IP. And, note that technical glitches can be resolved by rebooting only. Therefore, power down your Netgear device. Take your time. After you feel that your Netgear router has been given enough time to relax, power it up again. Now, see if the devices accessing the router’s WiFi are still getting different IP addresses.

Update the Firmware

Tried every hack and still the issue is not ready to set you free? Well, there are chances that there is new firmware available for your WiFi router. Know that firmware upgrades consist of new instructions for the Netgear router’s functioning. In other words, your router will no longer accept the instructions given by an older firmware version. Thus, update your Netgear router as soon as possible. You can do this either with the help of the Netgear Nighthawk app or via the web-based graphical user interface.

In Closing

The Netgear router keeps changing IP address issue can be a severe headache if not resolved timely. Considering this post was written to help you fix the same problem, we hope that now you’ve learned various hacks to do the same. This post will also help you prevent the generation of the same issue in the future. Thanks for reading!